임베디드 시스템 Jobs

I need an experienced PCB designer to take my concept all the way from a clean, well-documented schematic through to final production files. The board’s purpose is digital-only signal transmission, and it will revolve around a microcontroller core talking to several onboard sensors. Here’s what I expect from you: • A reviewed and ready-to-hand schematic with clear net naming and annotation. • Component selection focused on reliable microcontrollers and sensors; if supporting parts or alternative communication modules improve integrity, you’re free to recommend them. • A compact, manufacturable layout that respects high-speed digital design rules, proper decoupling, and clean ground referencing. • Full output package: Gerbers, drill files, pi...

Looking forward to working with a dedicated embedded systems expert.

I need a small pcb board powered by 9V battery that is connected with the board through a JST-ph 2.0 mm 2 pin connector The board has one 9V+ and 9V- output and 9V Input 1 en 2 with a JST-ph 2.0 mm 4-pin connector that will be connected with a healthcare sensor. The board has one 9V relays that will be active when input 1 is active, the relay has a NO/NC/9V- output with a JST-ph 2.0 mm 3-pin connector called "Fall" The board has one 9V relays that will be active when input 2 is active, the relay has a NO/NC/9V- output with a JST-ph 2.0 mm 3-pin connector called "Move" The third relay is for low battery detection of the 9V input. The system should trigger when the battery voltage drops to 6V or 10% of the full capacity. The relay have a NO/NC/9V- output with a JST-...

Hardware Design Requirements I need help reviewing and completing a custom embedded controller schematic and PCB based on an ATmega328P-PU. The application details are confidential. Please focus only on the hardware implementation. Microcontroller ATmega328P-PU 16 MHz crystal oscillator ISP programming header Reset circuit 5 V, 3.3V operation Power 12 V DC input On-board 5 V regulator for the MCU 12 V rail available for loads Proper power distribution and decoupling Inputs The controller monitors six analog/digital sensing lines. Input assignments: Input A0 Input A1 Input A2 Input A3 Input A4 Input A5 These inputs are used for continuous signal monitoring. Outputs The controller drives multiple indicator groups. Required outputs: Output Group 1 Output Group 2 Output Group 3 Outp...

I’m building a compact electrolysis hair-removal unit and need a full schematic and PCB layout that an assembler can take straight to production. Core requirements • Control core: ESP32 must set DC voltage (0–24 V), DC current (0–5 mA) and RF power (up to 2 W at 13.56 MHz). Hard cap current limit for DC, the power supply must be unable to supply more for safety. • Dual-path power: DC and RF run independently yet may operate simultaneously. The RF path travels down the probe needle, which is the DC low-side return. A bias-tee approach seems most practical; I’m open to alternative RF/DC combining networks if you can justify them. • High-side connection: the positive DC terminal links to a metal plate the user sits on. If a negative-rail design is e...

I’m developing a Graphical User Interface on an STM32F469 Discovery board and want it to look and feel like the demo in this video: My toolchain is TouchGFX together with STM32CubeMX and STM32CubeIDE, and I’m hitting the ceiling of what the tutorials on the web cover. Here’s what I need: • A hands-on example project that runs on the F469 and shows off complex, fluid animations, polished screen navigation, and a few custom-looking widgets so I can study and extend the code. • Guidance while we build it so I understand why each performance tweak or memory setting matters. • An honest assessment of whether the F469 can truly handle this level of visual richness; if not, point me to the exact board or MCU family that can, plus any advanced courses, bo...

I’m building an AIS-140 compliant tracking unit and need one partner who can take the idea from schematic to fully tested firmware in a single run. That means you will design the multilayer PCB, select components that satisfy ARAI / AIS-140 certification, and deliver production-ready firmware that handles GPS/GNSS acquisition, GSM/LTE data transfer, SMS fall-back, panic button logic, CAN interface, and standard-mandated encryption and packet formats. Scope • Complete schematic capture and PCB layout (Altium, KiCad, or similar) including Gerbers, BOM, 3-D step files, and assembly drawings. • Firmware in C/C++ (preferred on STM32 or an equivalent automotive-grade MCU) covering GNSS parsing, GPRS/LTE socket handling, FOTA, accelerometer-based tamper detection, and diagno...

I need a seasoned KiCad specialist to turn my wearable health-band concept into a production-ready, multi-layer PCB. The board’s sole purpose is data communication, and it must do so over Bluetooth using a Nordic Semiconductor microcontroller (nRF52 family or a comparable part you can justify). You will start from my block diagram and recommended component set, refine the schematic, route the multi-layer stack with controlled impedance for the RF section, and deliver gerbers, pick-and-place, and a clean BOM. KiCad 7 is preferred so I can review your work without back-porting issues. Deliverables • Complete KiCad project folder (schematic, PCB layout, libraries) • Gerber & drill files, assembly outputs, and BOM ready for a board house • Brief design repo...

I have a project that calls for a digital-only signal-processing circuit of moderate complexity. I already know the functional blocks I need, but I’m looking for a clean, production-ready schematic that I can move straight into PCB layout and prototyping. Here’s what I need from you: • A complete schematic (Altium, KiCad, OrCAD, or similar) with clearly labelled nets and hierarchy. • A concise bill of materials with part numbers that are currently available from mainstream suppliers. • Brief design notes covering key timing considerations, expected clock domains, and any special layout constraints. • Simulation or verification output that demonstrates the circuit meets the stated digital signal-processing function (SPICE, ModelSim, or an equivalent to...

I’m refining a compact control-circuit project that must live on a single-layer PCB. The board will carry a mix of surface-mount and through-hole parts, so the layout has to respect clearances for hand-soldered TH components while still keeping the SMD side tight and economical. All external wiring will come in through pin headers and terminal blocks only; no USB or other connectors are required. Please keep these plugins clustered along one edge for easy panel access. Because I need occasional face-to-face reviews and quick hand-off of early prototypes, I can only work with designers located in New Delhi (or who can meet there) for this project. This is important as the PCB design must align with specific enclosure dimensions that I'll provide during meetings. What you&rsquo...

أرغب في إنجاز مشروع تجريبي صغير لِعَدٍّ ثنائي البِت مبني بالكامل على الترانزستورات (من دون أي دوائر متكاملة). ما أحتاجه بالتحديد هو مشاركتي التصميم العملي للدائرة مع كل الحسابات وتوضيح المكونات، • أي لقطات محاكاة أو قياسات تثبت أن العداد يعدّ 00-01-10-11 بشكل متكرر. هذا الرابط يوضح ما احتاجه

Looking for an experienced Qt/C++ developer to support the software development of a Linux-based medical device platform. Work includes UI development (Qt/QML), hardware communication, software architecture, debugging, testing, and documentation in an IEC 62304-oriented environment. Experience with medical devices, embedded systems, Linux, CMake, and modern C++ is highly desirable. Long-term collaboration possible.

I need a redesign of an existing breakout board prototype with the following requirements: 1. Remove all pinholes. 2. Ensure the design is firm and avoids communication issues. 3. Dimensions should be 80x50mm, including holes for installing the board. 4. Include accurate routing of 60 lines end-to-end, aligning them with the 60-pin adapter provided in the attachment. 5. Incorporate FPC 40 and FPC 12 slots (0.5mm pitch). 6. Add 8 connections with 4x2 standard female pinholes (2.5mm pitch), aligned with the FPCs and routed to match the 60 pins of the adapter. 7. Follow the attached concept for reference, but ensure correct routing alignment for all lines. Deliverables should include updated source design files and Gerbers ready for production.

Our EdTech platform is expanding its catalogue of technical courses and I am ready to onboard seasoned instructors who can run live, highly-interactive online classes in Embedded Systems, VLSI, or AutoCAD. The sessions are delivered remotely, so you can teach from anywhere as long as your connection is stable and your presentation style keeps learners engaged. What the work looks like You will design a clear lesson flow, teach in real time via our virtual classroom (screen-sharing, whiteboard tools, live Q&A), and gauge learner progress through quick assessments or project checkpoints. All class recordings, slide decks, lab files, and code samples should be uploaded to the platform immediately after each session so students can review the material on demand. Key expectations &bul...

This project centres on a compact embedded platform that will sit inside an industrial automation cabinet and take charge of continuous monitoring and control. At its core the board must read an oxygen sensor, process the signal locally, apply any calibration curves, and then drive a pair of digital outputs that feed the plant’s PLC. A small TFT or OLED status screen and a Modbus-RTU port over RS-485 will round out the human-machine and network interfaces. I will provide the exact sensor datasheet, operating ranges, and the enclosure footprint; you handle everything from component selection to fully-routed Gerber files and production-ready firmware. Key deliverables • Schematic capture and multilayer PCB layout (KiCad or Altium) matching my mechanical constraints • BO...

Devo completare la logica di controllo per l’automazione di un processo industriale basato su PLC Siemens. Il lavoro comprende lo sviluppo del programma in ladder e blocchi funzionali (FBD), oltre alla diagnostica e alla messa a punto necessarie per garantire un funzionamento stabile nel tempo. Sto già gestendo l’hardware e la parte elettrica; mi serve quindi un supporto focalizzato sul software, dal primo sketch fino al collaudo finale. Saranno particolarmente apprezzati esempi di progetti simili realizzati con TIA Portal perché voglio capire in che modo la tua esperienza si traduce in velocità di sviluppo e affidabilità dell’impianto. Deliverable essenziali • File di progetto completo e commentato • Schema dei blocchi funzione...

I need access to the CAN bus communication of a 2010 Toyota Prius, specifically to diagnose errors in the battery management system (BMS). This is crucial for troubleshooting and ensuring the hybrid battery operates efficiently. Key requirements include: - Access to CAN bus data - Ability to extract and interpret error codes from the Voltage Sensor or monitor the sensor to ensure it is operating correctly Ideal skills and experience: - Experience with automotive CAN bus systems - Knowledge of hybrid vehicle battery management systems - Proficiency in reading and analyzing CAN bus data Please provide a detailed approach and timeline with your bids.

I'm looking for a developer to create a Building Management System (BMS) for the savic-net G5 building. This system should be built on proprietary software. Key functionalities required: - Energy monitoring - HVAC control Ideal skills and experience: - Expertise in developing proprietary software - Experience in energy monitoring and HVAC control systems - Knowledge of building management technologies Please provide a portfolio with relevant experience.

I have a prototype that has to drive two independent BLDC motor drivers from a single hobby-grade RC transmitter. Both motors must respond to the same handset, with full speed and direction control on each channel. The throttle stick should give smooth, variable speed rather than stepping through fixed levels, and the entire solution needs to stay as compact as possible so it can fit inside a small housing I already have. Here is what I need from you: • Hardware: a complete schematic and compact PCB that takes the receiver’s PPM and feeds two BLDC driver stages. Component selection should balance size, thermal performance, and ready availability. • Firmware: clean, well-documented code that reads the RC signals, maps them to forward/reverse and proportional duty cycle ...

we would like to make oxygen analyser using below sensor

ABOUT THE PROJECT We manufacture atmospheric water generation machines deployed in RVs across multiple regions. We need a Raspberry Pi to act as a remote management gateway—reading machine status, executing commands (power on/off, settings), and sending data to the cloud. **Why this matters**: Units are mobile and customer connectivity is unreliable. We need **independent cellular connectivity** (4G/LTE with SIM card) to ensure Air Water can monitor and control the fleet 24/7, regardless of user behavior.

我已从设备上安全拆下 7037IC 芯片，物理状态完好。现在希望在对芯片零损伤的前提下，一次性读取出其中的手机操作系统固件。为协助你完成工作，我可以提供： • 高分辨率引脚照片 • 电路连接信息 • 芯片实物寄送 首选方案是使用 JTAG 工具；若你建议配合 ISP 编程器、NAND Flash 编程器或其他专用设备，也请说明理由与流程。此外，请注明您所用的提取设备型号。 交付要求: 1. 读取并生成完整可验证的操作系统固件映像（BIN 或 HEX）。 2. 同步提交哈希值或其他完整性校验证明，确保数据无缺失、无篡改。 3. 附一份简要读取日志或说明文件，便于我后续分析。 4. 如在提取过程中顺带获得基带或引导固件，请仅在说明中备注，交付物仍以操作系统固件为准。 我们优先寻找对苹果手机芯片底层代码有深入了解且具备苹果电池7037IC芯片相关经验的专业人士。期待你分享过往使用 JTAG（或相关工具）成功提取芯片数据的案例，说明所用设备、步骤及为何对芯片安全。请在接手后于一个月内完成全部交付。 如果你擅长精确引脚定位、信号完整性处理、低电压读取等细节，欢迎提出你的方案——我会根据专业程度与成功率优先选择合作。

I need clean, reliable firmware that will sit on my existing RTU hardware, pull live sensor readings, and publish them to my cloud broker over MQTT. The focus is squarely on accurate data collection from the attached sensors and timely transmission upstream; no local heavy processing is required right now. You will work directly in the device’s embedded environment, set up the drivers for the connected sensors, handle the sampling schedule, form properly structured MQTT messages, and make sure every reading reaches the server even in spotty-network conditions (re-connect logic, message queuing, QoS handling, etc.). This project requires an experienced embedded code developer who can deliver quick turnaround times without compromising quality. Previous work on similar projects is h...

I'm seeking an experienced engineer to connect push-button electronic switches to linear actuator mechanisms. This setup is intended to automate a process. Key Requirements: - Expertise in integrating electronic switches with actuators - Proficiency with push-button switches and linear actuators - Knowledge of automation systems and safety protocols - Strong problem-solving skills Ideal Skills and Experience: - Electrical engineering background - Hands-on experience with automation projects - Familiarity with wiring and circuitry Please provide examples of similar work and relevant qualifications.

A dedicated PCB will drive a self-service car-wash “vendo” unit built around an Arduino Nano. The board must accept the pulse output from a standard electronic coin slot, translate each valid coin into the required runtime, and use that signal to energise five independent relays that handle pumps, valves, or lights. All relays share a common 12 V source, yet the Nano and logic lines stay safely at 5 V, so on-board regulation (12 V → 5 V buck or linear, as you judge appropriate) is part of the layout. The relays themselves need fly-back protection, status LEDs, screw-terminal or JST headers for easy field wiring, and clear silkscreen labelling. A USB-B or tag-connect footprint for in-circuit programming is also required. Deliverables • Complete schematic (KiCad...

I need a compact, production-ready circuit board that acts as the main control system for a self-service car-wash vending unit. Its first responsibility is to handle payment processing—accepting coins, bills, and potentially a simple cashless module—then trigger the wash cycle once payment is validated. You will translate this into a complete hardware package: schematic, multilayer PCB layout, and a cleanly organised BOM with readily available components. I will provide the pin-out for the existing coin validator and the relay map for the wash equipment; you make sure the board routes power safely, isolates high-current lines, and exposes clean connectors for future add-ons such as water-flow control and a small customer display. Because the installation sits in a damp ou...

I have an all-analog circuit that I now need translated into a clean, production-ready hardware package. The job is two-fold: first, capture the complete schematic; second, turn that schematic into a compact, battery-powered PCB layout that is ready for fabrication. Because every stage is strictly analog, component placement, trace routing, and grounding must be treated with the usual care to keep noise and drift to a minimum. The board will run solely from a battery supply, so please incorporate thoughtful power-rail filtering, low-quiescent-current regulators where helpful, and clear test points for current-consumption checks. I’m comfortable with KiCad, Altium Designer, or Eagle—use whichever you prefer, as long as the final files are fully editable. Deliverables • E...

I need single-sided, double-sided, and full multi-layer PCB layouts created for mixed-signal work. The boards combine analog and digital circuitry and will be used across embedded control, RF, and other high-speed applications, so careful impedance control, differential-pair routing, and solid mixed-signal grounding are essential. Altium Designer is my main environment, yet I can seamlessly integrate files produced in Proteus, KiCAD, Eagle CAD, EasyEDA, or even Multisim, so feel free to use whichever of those platforms fits your workflow best. What I expect from you: • Complete schematic capture and net-validation • Fully routed PCB layout that passes DRC and is ready for fabrication • Gerber (or ODB++) files, drill data, and a clean BOM suitable for procurement ...

I am looking for an experienced PLC programmer to do on a small CODESYS 3.5 automation project. The task involves creating a simple sequential control process using sensors, motor control, a loading gate, and a 10-second timer.

I have a complete written pinout for a small board built around an ESP32-WROOM module, I have the circuit assembled with bare wires and I now need that schematic made in cad as a two-layer PCB in KiCad. The board will have two LDO regulators, a TP4055 Li-ion charger, an STI3408B buck converter and a 24-pin FPC connector for a camera, and assorted passive components. The more compact the pcb the better. You will receive: • the pin-by-pin connection list and a sample kicad assembly with the components all on it. What I expect back: • the complete KiCad project (schematic, PCB, libraries) • production-ready Gerber/NC drill files

Je développe une nouvelle smartwatch et j’ai besoin d’un·e expert·e capable d’intégrer un système de notifications centré sur la connectivité. Objectif principal – Notifications et connectivité fiables entre la montre et un smartphone (Android et, idéalement, iOS). Fonctionnalité prioritaire – Réception d’emails : la montre doit afficher un résumé clair du message (expéditeur, objet, premières lignes). Points d’attention – Gestion efficace de la synchro en arrière-plan pour limiter la consommation d’énergie. – Interface utilisateur fluide : aperçu du mail sur l’écra...

I need a purpose-built Electronic Speed Controller for my electric glider that runs on 3-6 cell Li-Po packs (8.4 V – 11.1 V). The unit must deliver: • Responsive throttle control for a brushless motor • Integrated battery management with safe low-voltage cut-off and, if practical, basic current limiting • A reliable brake function to stop a folding prop cleanly in flight Compact size, light weight and maximum efficiency are important, as the airframe has limited space and every gram counts. Here is what I would like from you: 1. Schematic, PCB layout and BOM (KiCad, Altium or similar) 2. Firmware source code with clear parameter tables (C / STM32, ATMEL AVR or comparable MCU) 3. Simple desktop configuration tool or clear CLI instructions so I can adjust ti...

Project Title: Low-Power Cellular IoT Predictive Maintenance & Leak Detection System Project Overview: We are seeking an experienced developer to design and prototype an integrated, low-power, battery-operated IoT device utilizing an off-the-shelf cellular prototyping architecture (e.g., Particle Boron or Blues Wireless Notecard). The device will perform twin monitoring tasks: physical leak detection via a traditional sensor, and mechanical predictive maintenance via Acoustic Anomaly Detection (AAD). The system must run on a battery budget that supports deep sleep, waking up instantly on a leak interrupt or periodically on a timer to perform a self-test and acoustic health assessment. Data must route through a cloud middleware layer via webhooks to a custom website dashboard, with cri...

I need a clean, well-documented I2C driver written in C for my STM32 board. The driver must operate in both master and slave modes while staying strictly within the 100 kHz Standard-mode specification. Full read and write transactions are required in each role, including proper start/stop sequencing, ACK/NACK handling, and error recovery for bus faults or time-outs. My current firmware is built with STM32CubeIDE, so the new module should compile there without warnings and slot neatly into the existing HAL-based project structure (pure LL implementations are also acceptable if you explain the integration steps). Deliverables • Source and header files with clear, line-level comments • An initialization routine that lets me choose master or slave at runtime • Blocking...

I'm looking for an experienced PCB designer to create a control board for my standby generator. The PCB should manage an Automatic Transfer Switch (ATS) and engine control, and should include: SPARXX ATS REV A – PCB DESIGN SPECIFICATION Project Design a production-ready PCB-based Automatic Transfer Switch (ATS) controller to replace an existing relay/timer panel while maintaining the same operating logic. Deliverables Required Complete KiCad 9 project Schematics PCB Layout BOM Gerber files Pick and Place files Programming header Source files PCB Size Approximately 3.5" × 7" × 0.5" maximum Reserve approximately 20% of board space for future expansion. Power Inputs: 120 VAC 12 VDC Generator Supply Board must automatically power from either sour...

I'm looking for a skilled engineer to design and develop a GPS receiver primarily for navigation transmit and receive the signal over rf antenna Key Requirements: - The GPS receiver should provide accurate and reliable navigation data. - It must be designed to integrate seamlessly - The design should prioritize user-friendly interface and experience. Ideal Skills and Experience: - Proven experience in GPS technology development. - Strong background in hardware design and software integration. - Ability to create detailed, technical project proposals. Please include detailed project proposals in your application.

I already have a partially-working prototype for an industrial counter + timer built around an Arduino. It needs to count production units while tracking elapsed time in parallel, show both values on an LCD screen, and push the data over Wi-Fi to my factory LAN. Where I’m at • Core hardware is assembled and a rough sketch is running, but the logic occasionally drifts and the Wi-Fi payloads are not stable. • The prototype can be shipped to you immediately, fully labelled and with a wiring diagram of the current build. What I need from you 1. Clean, well-commented Arduino code that reliably performs the simultaneous counting and timing functions. 2. Solid LCD interface: clear, easy-to-read formatting of count, timer, and simple status icons. 3. Robust Wi-Fi routin...

I'm seeking an experienced electronics prototyper to create a functional demo of a wearable ultrasound device. Key Requirements: - Design and build a prototype of a wearable ultrasound device - Ensure the prototype is functional and suitable for demonstration purposes Ideal Skills and Experience: - Expertise in wearable device technology - Strong background in ultrasound technology and electronics - Proficiency in prototyping and functional demo creation - Experience with embedded systems and IoT is a plus Please provide examples of previous related work and a rough timeline for completion.

I’m building a handheld device that lets me roll a ball across any flat surface and have it actively steer itself so the pen mounted inside draws in the exact direction I choose. An optical-flow sensor will read surface motion, my code will translate that into heading commands, and two small motors inside the ball will supply the corrective spin. The overall sketch is already under way, but I need a specialist who knows Arduino-style hardware and, more importantly, how to marry miniature motors with an ESP32-C module for precise directional control of the ball. Your main focus will be advising on the right motor format, driver circuitry, power budgeting, and the physical/electrical integration so the firmware can call simple functions like setHeading() or setVelocity(). I’m ...

I’m bringing a brand-new electronic charger to market and need an engineer who can turn my concept into a fully working prototype. The focus of this engagement is the complete design and prototyping phase—circuit architecture, component selection, enclosure layout, PCB, and initial functional build. Compact size is the single most important design driver, so every decision—from transformer topology to enclosure wall thickness—has to work toward a slimmer footprint without compromising safety or performance. I’m open to creative approaches such as GaN or other high-efficiency solutions if they help us meet that goal. To move forward, please send a detailed project proposal that outlines: • Your approach to achieving a space-saving form factor • Mi...

I want to turn a concept for a pneumatic actuator into a working prototype that can grip or clamp objects with repeatable, controllable force. The job spans mechanical design, pneumatic circuit sizing, and the embedded-software layer that will let me test different grip profiles through a simple interface. Scope • Translate my sketches and performance targets into detailed CAD ready for rapid manufacture (CNC, SLA or FDM are all fine). • Select off-the-shelf valves, fittings and sensors, then size the cylinder and air supply so the gripper reaches its force and stroke goals. • Develop quick-change firmware or a ROS/Arduino node that lets me adjust pressure, speed and dwell time from a laptop while logging position/force data. • Assemble and bench-test the unit,...

Scope of Work AI/ML-Based Predictive Active Hydro-Pneumatic Suspension Control Software Development Project Overview We are developing an Active Hydro-Pneumatic Suspension System for a heavy off-road defence/mining vehicle. The mechanical suspension, hydraulic system, proportional valves, ECU hardware, and sensors are being developed in-house. The objective of this project is to develop an AI/ML-based suspension control algorithm capable of operating in two configurations: Configuration A: Accelerometer-based Active Suspension Control. Configuration B (Optional): LiDAR-assisted Predictive Active Suspension Control. The software shall automatically control the proportional hydraulic valves to achieve optimum ride comfort, vehicle stability, and suspension performance. Scope of Developm...

We are Unikeyic, a global electronic components distributor, and we are looking for experienced technical writers for a long-term collaboration. If you have a background in electronics engineering and enjoy writing high-quality technical content, we'd love to hear from you. What You'll Do You will write original technical articles related to electronic components and circuit design, including topics such as: Semiconductor devices Passive components PCB design Embedded systems Power management Electronic component selection Industrial automation IoT applications Electronic engineering tutorials The article title, outline, target keywords, and writing requirements will all be provided by us. Requirements To be considered, please make sure you meet most of the following require...

我正在推进一款基于 SN7037 BOHT 的项目，需要与你一起完成整套烧录方案与量产资料。整个开发分为三阶段：前期验证、过程中跟进、最终交付，目标是在一个月内封闭完成。 前期验证 • 先行进行“验证空裸芯片测试”，确认空裸 IC 的可编程性与稳定性。 • 我会准备并邮寄样板给你方烧录，来回寄送完成功能验证。 • 我们共同“明确验证周期”，并在节点表里锁定每项里程碑。 关键技术挑战 目前最关心的问题是“是否能在空板子、无数据的状态下，直接对整板烧录”。同时，也需要你评估信任链、EFuse、PUF 等配套方案的可行性，但重心仍放在整板一次性烧录路径的落地。 项目进行中 我希望每周收到一份进度报告，内容包含： 1. 已完成工作与当前状态 2. 下一步计划 3. 风险或需求 同时，所有提取到的加密或配置内容需同步提供验证包，以便我端随时复测。 验收标准 以下 5 项全部通过即视为成功： 1. 兼容 iPhone 11–16 机型 2. iOS 18–27 联网不弹窗（需说明可保证的周期） 3. 系统内不显示未知部件 4. 通过 AST 诊断 5. 苹果健康度显示正常 最终交付物 • 完整烧录文件（含密钥/配置） • 烧录座与工业量产上位机软件 • 生产所需全部文档、流程与 BOM • 简明售后方案，说明常见小 BUG 的修复流程与响应时限 请在提案中列出你将采用的工具链、预计的日程以及售后支持周期。我期待与你协作，将这套 SN7037 烧录方案快速落地。

Project Description Bullet Points Project Overview: Develop an AI-driven management and reservation system for EV battery swapping stations. The system will enable users to monitor battery health (State of Charge/State of Health), locate available stations, and reserve battery slots in real-time. Core Functionality: User Interface: Create a dashboard/mobile app for users to track battery status, view station availability via GPS, and manage reservations. IoT & Hardware Integration: Interface microcontrollers (e.g., ESP32/Arduino/Raspberry Pi) with sensors (voltage, current, temperature) to transmit real-time data to a cloud server. AI/Predictive Analytics: Implement AI models to optimize charging strategies, predict battery health, and forecast station demand. Backend & Cloud:...

I have a couple of small IoT units here in Hamilton, ON (L9C 6A4), I need someone who can come to the house with Microchip’s IPE and the right programmers, connect to each board, and load the latest firmware. I will supply the compiled HEX files and the client will perform the test. All you need to do is bring the hardware (PICkit, SNAP, or similar), verify each flash. If you’re local, equipped, and comfortable doing house calls, let’s set a time.