마이크로콘트롤러 Jobs

Humidity temperature timer controller program

A program for a Siemens Logo PLC to control a motor – (0 – 10Volt or 2 – 20 mA output) Two triple pole rotary switch inputs – (9 possible results) Rotary switch No. 1 selects dose value, namely 7.5ml, 9ml & 11ml – (the values are recorded in a table that can be changed by a supervisor) Rotary switch No. 2 selects the dose strength, namely 1x dose, 2x dose or 3x dose – (the values are recorded in a second table to enable the supervisor to change the value of 2x & 3x if required e.g. 1x dose, 1.5x dose or 2.2x dose) The run function will only give an output if both switches have a value selected, ie, if Rotary switch No. 1 or No.2 is on position 0, there will be no output value. The output value in each of the 9 possibilities will relate to the a t...

We have converted the A series PLC with NSD encoder & its converter VS-1S62 to Q series PLC with same encoder and its converter VS-Q62B-M2PG. There is a difference in the parameter settings. The new Q series converter is not supporting some parameter settings as A series converter. And also we don't have comments on the existing PLC program. If anybody can help on this, Please message me.

A program for a Siemens Logo PLC to control a motor – (0 – 10Volt or 2 – 20 mA output) Two triple pole rotary switch inputs – (9 possible results) Rotary switch No. 1 selects dose value, namely 7.5ml, 9ml & 11ml – (the values are recorded in a table that can be changed by a supervisor) Rotary switch No. 2 selects the dose strength, namely 1x dose, 2x dose or 3x dose – (the values are recorded in a second table to enable the supervisor to change the value of 2x & 3x if required e.g. 1x dose, 1.5x dose or 2.2x dose) The run function will only give an output if both switches have a value selected, ie, if Rotary switch No. 1 or No.2 is on position 0, there will be no output value. The output value in each of the 9 possibilities will relate to the a t...

Hi, I've got an LTE router that needs a Quectel CAT4 module soldered onto it. I've got the module, I'd like to bring it in to be soldered onto the motherboard. Is this something you can price me on? Cheers! Sam

I need a firmware for faculty for the arduino to communicate with the CH376S (via UART) and write a text file located on a DS card drive connected to the CH376S, when connecting the Pen Drive to the USB connector of the CH376S they are transferred to the pen drive the file: Temperature, date and time saved on the SD card separated by date.txt. This is the first stage of a larger project, so this could lead to more work. Sorry for my English, I'm Brazilian.

A PIC18F25k22 development board and HD44780 LCD board along with your ICD4, The embedded system has an analogue input connected to AN4, an 8-way DIP switch connected via the SPI bus and an LCD connected in 8-bit mode to POTR B of the microcontroller. The lcd should initially show a two-line message – ‘Welcome to’ on the top line and ‘Embedded Systems’ on the second line. After a short delay this should change to displaying the adc value on the top line and the DIP switch value on the second line with suitable user interface information telling the user what the display is showing.

It should be portable (running on battery) and should have an auto-cut option once the temperature reaches desired value a small motor for stirring the water. None of the mechanical components fall under this scope. Just need off-shelf components to design a circuit.

I have a board working on 5v, I am looking for someone professional to add a DC to DC 5v to 12v step up converter for one unit only on this board. I need to be able to disable and enable this converter by using a sort of a jumper/switch. The kicad, BOM, CPL, and gerber files are ready. I am expecting the freelancer to edit his modifications into these files and make them in the correct format for JLCPCB order.

I need an Arduino code the test the full write and full read operations for the 24LC512 memory using the Arduino Nano Board.

this project includes UART touch screen in which touch screen will communicate to micro via UART port . Input instructions from touch screen & output through Micro GPIO. Touch will control GPIO . thats only functionality Deliverables :PCB Schematic with Gerber file Code

Hello, My task is about to design charging and discharging circuit for an fuel cell voltages. I.e., 5 charging stages with 1 discharging circuit varies with higher voltages 240V to 480V. I already designed the circuit but I need to make some changes. So I need help in that.

read the eva-dts data with Arduino and DDCMP protocol

Want to design a circuit diagram for a controller with functions like inbuilt voltage regulator, temperature control, tens, pemf, photon lights etc

I'm looking for an expert in Arduino firmware and driver libraries. The goal is to create a library for a variety of sensors/modules controlled by Arduino Nano. We would start with simple modules (buttons,buzzer,accelerometer,…) then next jobs would involve harder ones (Ethernet,oled,wifi,etc.). We already have a few modules done that can be used as template. We are looking for someone who would like keep working with us for more modules in the near future if possible. All your code will be tested with the real modules so you must know how to debug and fix if needed.

INKJET MANUFACTURER SEEKING EMBEDDED CHIP ENGINEER TO REVERSE ENGINGEER INKJET PRODUCTS. INDIVIDUAL NEEDS TO BE PROFICENT IN PROGRAMMING LANGUAGES SUCH AS C OR C++. STRONG KNOWLEDGE IN PROTOCOLS LIKE I2C, SPI, UART AND ISO 7816. INDIVIDUAL NEEDS TO HAVE THE ABLITY TO ANALYSIS COMMUNICATION SIGNALS BETWEEN PRINTER AND INKJET CARTRIDGES, CRYPTOGRAPHY USING LOGIC ANALYZERS OUTPUT PROJECT IS FOR PREFFERED INDIVIDUALS FROM THE INKJET INDUSTRY WITH 5-10 YEARS EXPERIENCE, USA CITIZENS AND OR NEW YORK RESIDENTS

I am looking for a talented freelancer to help me out with a project involving coding in Microchip Studio ATMega4808. The purpose of this project is to create firmware for a product design. The development environment for this project will be the Microchip Studio ATMega4808. Programming language of choice is C or C++. I'm expecting a freelancer with deep knowledge and experience with C programming language. If you think your skills might be a good match for this project, please get in touch.

Dear sir or madam. I would need help with programming. I already have an arduino program for my design (pcb with atmega328 ic) - it is about temperature regulation and also I use 1.3inch lcd display with ST7789 board for showing data. The problem is that if the screen freezes, it doesn’t refresh automatically and stays freezed (I need to unplug and plug again the power). I would probably need separate program for the screen, which would recognize when the screen freezes and then refresh it. Or do you maybe know any other solution? I hope that someone could help me. Have a nice day! Gašper Vidmar

We are in the end phase of developing several new tabletop products for the professional food industry. We want to create a great user experience for the interface. The first project would be to take over the software from one of our R&D partners - he makes the PCB prototypes and some of the mechanical solutions. Originally we just wanted to use DWIN but as he changed to a Raspberry screen, he programmed something in Python PyQT just as a method of controlling the product. It works, but it needs a talented UX developer to create a far more intuitive and more attractive interface. We would also like to add a language pack. Originally we just wanted to use DWIN but as he changed to a Raspberry screen, he programmed something in Python PyQT just as a method of controlling the produ...

Ζητείται άτομο για την απλοποίηση ενός τηλεκατευθυνόμενου οχήματος ( το παρέχω εγώ) που μέσω Arduino να ανιχνεύει ζωή.

PLEASE DO NOT BID IF YOU DO NOT KNOW BECKHOFF PLC AND TWINCAT C++. I need a project which has following features: 1. Get a byte[] package from UDP (if you have any PLC or access any real-time network card). 2. If you do not have any PLC or real time network card, you can use a simple ADS application by using C# which send sample data to PLC by using ADS library. 3. Read byte[] from PLC after that convert and save "protobuf" object. This part should written by using C++ in TwinCAT. You should you Visual Studio 2019. Important Note: No place holder bids! Thank you.

Interfacing a Dwin HMI display to display a string at a specified address via an Arduino Arduino used should be Arduino mega 2560, the given dwin HMI display is DMG80470C070_15WTR Arduino is connected via a TTL<->RS232 convertor to the display the string obtained, which is to be displayed on the display is variable in nature and will change into the corresponding value in the full program this snippet is designed to slot into

Create schematics and PCB layout based on the existing project design. The PCB should be designed in a way that it is easy to assemble and manufacture. Pick an appropriate microcontroller based on the requirements of the project. The microcontroller should have enough processing power and memory to handle all the required tasks. Consider factors such as cost, availability, and ease of programming when selecting a microcontroller. Add a gyroscope to the design. The gyroscope should be selected based on the required range, sensitivity, and accuracy. It should be compatible with the selected microcontroller and should be able to communicate data to it. Consider adding an accelerometer to the design, if required. The accelerometer should be selected based on the required range, sensitivity, an...

Hello, I have attached two files for the project I am working on, the pdf form is the book of the project, and the DOCX form is the part that I need you to show me how to put it together through a video call (explain to me how to put it together or if you can build it and send it untel 29.3.2023) I want to build it on a matrix as model so I can show it off the basics of the build on the matrix: converter: voltage output 12V DC/DC BUCK voltage output 12V DC/DC Boost Inverter: AC +-12V/ AC +-230V 50Hz 12V DC/+-12V AC the goal is to charge two batteries 12 A suitable transformer for the system: 12V AC/230V AC all of this system is based on a micro controller (raspberry pie model b) I need it done before 29.3.2023

I'm looking for a freelancer to help me connect a Windows 11 PC to an unknown USB device and dump the firmware. It is a handheld device and a USB connection will be needed. The freelancer will need to be able to read and write the firmware from the device. All details should be carefully handled and no malicious data or code should be written to the device or sent over the network. The device should not be damaged or modified in any way. The output of the project will be the firmware for the device which must be isolated and kept secure with the capability to rewrite the firmware back again (or after modification). An ability to decompile/analyse the firmware once downloaded would generate another project of similar worth. At the moment I cannot find any USB drivers for this unit. ...

We seek an experienced engineer to enhance the design and build a device that can obtain fingertip photoplethysmography data at a wide range of wavelengths. We have designed and constructed preliminary prototypes based on published information using commercially available parts. An independent contractor who performs this work should have experience in circuit design, microprocessor control of light emitting diodes, laser diodes, and photodiodes, and troubleshooting acumen regarding signal transmission and reception and optimizing signal-to-noise ratio in the device.

보다 자세한 내용을 확인하시려면, 회원 가입 또는 로그인 절차가 필요합니다.

I am looking for an experienced programmer to create a firmware program for an MSP430 microcontroller, using the Code Composer Studio (CCS) platform. This will involve strong coding proficiency in C languages, as well as familiarity with MSP430 and the CCS platform. I do not have source code available for this project; the programmer will be required to create the program from the ground up. I do have a specific hardware requirement, namely the MSP430 microcontroller, which must be compatible with the CCS platform. The ideal candidate should be a reliable and detail-oriented programmer with expert knowledge in coding in C languages and a proven history of successful completion of microcontroller programming projects. A strong understanding of electronics is also essential to ensure the...

Hi, looking for someone who can help me to get access to an Aurix Microcontroller. Basically I need to be able to access and read/write the areas, such as BROM, HSM, PFLASH AND DFLASH. Need also assistance on how to connect the correct debugger. Thanks

I'm looking for a Freelancer to develop a software driver to control a sensor using SPI communication over an STM32 Microcontroller. For this project, expertise in embedded C is required. Unfortunately, I do not have an existing library for this driver, so one will need to be created from scratch. The driver also requires unit testing for debugging and validation. Therefore, experience in debugging and unit testing is preferred. I have the electronics ready to go to test the driver, etc.

Is there any posible way of measuring moisture in grain with arduino? What sensor to use? Are there any cheap sesor which can do that?

We have a bottle stickering line where bottles go over a Assembly line where the bottle goes through a product sticker (marked with a laser sensor). when the laser sensor has been triggered a new label will be pushed foward for the next bottle. This system is now broken. This works with a HMI touchscreen. The manufacturer does not respond back, so we need to make a new solution. I am thinking about a arduino/esp32 for the coding. We have relais, the wave a plc controller type: DVP-14SS2 (if even needed) We have a large steppenmotor and a label reading unit (that can be ignored if we use the sole steppenmotor). Can someone help us with this so that the sticker unit can work again. We have many more projects within our company, so it will be a longer cooperation.

I have a battery cell balancer with a Bluetooth app, I have already wired a UART-USB converter to the chip and I am reading data successfully from balancer via Termite. I only need to analyze this data now and write code to display cell voltages. This is data I am receiving from Termite: I have the protocol document also 05 2c 02 2b 56 01 02 02 3a 6a e2 6e 1b 08 02 02 .,.+V...:jân.... 22 03 02 20 02 02 02 02 fc 1d 24 81 60 5e 00 02 ".. ....ü.$`^.. 42 95 07 d5 17 fc 02 02 02 80 06 02 02 02 02 02 B•.Õ.ü...€...... 32 2 1d 2f 81 61 5e 00 02 42 95 07 d5 1f fc 02 02 02 ./a^..B•.Õ.ü... 80 06 02 02 02 02 02 12 €....... 19 24 81 60 5e 00 ...

We are an office with countless files. To make it easier to find these files in the future, each of them is to be fitted with an RFID sticker. About five rooms are to be equipped with a UHF reader on a Raspberry Pi. At one workstation, it should be possible to assign RFID stickers to files; this should be made possible via a web interface. It must also be possible to search for files via this web interface. This includes the name of the file, the file number and the RFID code. All UHF readers should then be addressed via a "Find file" button and search for the file (or the RFID sticker). The reader that receives the strongest signal should report that the file is in its vicinity. also we need to use a reader with a wide range, probably at lease 5 meters indoors

Need to control two digital outputs based on one analog input using st32 mictrocontroller

L'attività consiste nell'implementazione di un firmware su microcontrollore per gestire sensori esterni su bus e driver led. Attività in presenza a Dalmine (Italy)

Hi review the code for controlling stepper motor using joystick and check distance by ultrasonic module that written by arduino ide and accel library

Hi, I need to program the LILYgo 7000G board to communicate via MQTT via LTE and wifi. It is also required to read the GPS position. Regarding the power part, it is necessary that the board goes into deep sleep consuming in general less than 50 ua/hour. To achieve that it should be possible to turn off the SIM7000G via software through the ESP32 and put the ESP32 into deep sleep. It would be necessary to see the rest of the electronic components and their power consumption.

We have a bottle stickering line where bottles go over a Assembly line where the bottle goes through a product sticker (marked with a laser sensor). when the laser sensor has been triggered a new label will be pushed foward for the next bottle. This system is now broken. This works with a HMI touchscreen. The manufacturer does not respond back, so we need to make a new solution. I am thinking about a arduino/esp32 for the coding. We have relais, the wave a plc controller type: DVP-14SS2 (if even needed) We have a large steppenmotor and a label reading unit (that can be ignored if we use the sole steppenmotor). Can someone help us with this so that the sticker unit can work again. We have many more projects within our company, so it will be a longer cooperation.

ADS installation and previous experience with RF Power amplifier design in ADS are required.

The below link is an way to update firmware of Canon IP series printers with internet. ~/how-to-update-the-printer-firmware. I need an engineer how to update firmware of Canon IP series printers without internet.

We are looking for a programmer to build a basic plc to control a mobile dust suppression machine. There is 12 digital inputs, 8 analog inputs and 16’digital outputs in the project Flexible with hardware to suit programming language skills of applicants

However, instead of physically designing the board, the designer will create a digital representation of the PCB using specialized software. This digital file will contain all of the information necessary for the manufacturer to fabricate the physical board. During the design process, the designer must consider factors such as signal integrity, power distribution, thermal management, and manufacturability. These factors can have a significant impact on the performance and reliability of the final product. Once the digital PCB design is complete, the designer will generate manufacturing files that provide the necessary information for the manufacturer to produce the board. This includes information on the size and shape of the board, the location of components, and the routing of electric...

I have a Radar Sensor (IVS-947). Link: Datasheet: attached You need to write code for NUCLEO-F411RE board which will be connected with IVS947 radar sensor. The code should able to read number of moving objects within 80 meters, distance and their speed. The code can be developed in keil or STM32Cube. You should read the datasheet and write the connection between NUCLEO board and sensor. ** You must use Arm_CMSIS_DSP library for fast Fourier transformation which is the key for object detection. **It is needed to provide a simple GUI using matlab/python. Reference: attached

Hi, I have a small sailing boat which is moored in the middle of an harbour. I would like to monitor using GPRS 2G network (via Telegram) or SMS the following itens: -gps position. -temperature and humidity using the Dht11 sensor. -battery voltage. -water on the bilges. I would need also alerts for low voltage on the boat battery or high bilge water level. I have been successful in measuring the Dht11 output using WiFi and the following tutorial: However can't do it using WiFi. I'm using the TTGO T-Call V1.3 ESP32 sim800l board and dht11 sensor. Would like to continue to use the same hardware in the project. Could you please provide me a quote for the development of the code? Best Regards

Necesito crear un software que conecte simulador de vuelo con placa basada en Arduino. Para entrada y salida de switch , led, encoder.

I want someone experienced person to solve this task ,need a Arduino ide program for esp32 or esp8266 with TTl to Rs 485 converter to read modbus holding registers of any device,with wiring diagram.

I need a programmer who can make software of prepaid module with an RFID chip. It uses STM32 and MFRC630. I will share the prepared PCB design. The software will be developed accordingly.

An experienced embedded systems expert, specialize in hardware debugging, software development using C, and physical prototyping. extensive experience in system design, firmware development and debugging , skill set includes assistance with physical prototyping I have a ready-made project that works in the software mplab and proteus, but I'm having a problem with the hardware. The LCD screen does not display in the data. So I need help to make it running in hardware.

I would like stabilise PWM output of CH552 mcu