Find Jobs
Hire Freelancers

CANSnifferDigiout

€250-750 EUR

종료됨
게시됨 6년 이상 전

€250-750 EUR

제출할때 지불됩니다
We need a MCU hardware programmer to do following: 1)Any languageis accepted and can choose the mcu brand/model but it has to be cheap, very Small size, automotive, smd, internal flash memory, CAN network integrated (2 inputs CAN H CANL 100 kbit/s, 125 kbit/s, 250 kbit/s, 500 kbit/s and 1 Mbit/s), at least 4 digital outputs for the future, one PC flash/com port and easy flash process and already made software for this purpose, ROM read protected. Routines need: 1) Autodetect and connect to Automotive CAN Network. 2) Check MCU Eeprom Subroutines enable/disabled 3) Query CAR VIN (mode 9 pid 2). IF VIN is the same in the internal EEPROM enable the next routine. IF CAN VIN query = 000 or not found on network or if VIN is Different from eeprom don't enable Routines 1st preset CAN (see below) IF VIN is null in internal Eeprom then store the this value. 4)Searches 1st preset CAN Automotive command Sequence and then if found preset number of times / first 2 minutes (timer) after powered on, Enable up 4 digital outputs until next power up(not store this state in Eeprom). 5)If found 2nd preset CAN Automotive command Sequence, Clear internal Eeprom VIN 6)If found 3rd preset CAN Automotive command Sequence, Enable internal Eeprom VIN Check Routine 7)If found 4rd preset CAN Automotive command Sequence, Disable internal Eeprom VIN Check Routine 8)If found 5rd preset CAN Automotive command Sequence, Disable Digital Output control routine (Eeprom) 9)If found 6rd preset CAN Automotive command Sequence, Enable Digital Output control routine (Eeprom) 10) the preset commands sequences and timer must be editable by admin by serial/rs232 flasher interface
프로젝트 ID: 15879521

프로젝트 정보

11 제안서
원격근무 프로젝트
활동 중 6년 전

돈을 좀 벌 생각이십니까?

프리랜서 입찰의 이점

예산 및 기간 설정
작업 결과에 대한 급여 수급
제안의 개요를 자세히 쓰세요
무료로 프로젝트에 신청하고 입찰할 수 있습니다
11 이 프로젝트에 프리랜서들의 평균 입찰은 €596 EUR입니다.
사용자 아바타
Hi, I am a post graduate power electronics engineer and having very good experience in product design and development. I am excellent in embedded design & programming using pic, dspic controllers and MATLAB codding for Power projects, Boot loaders, Bluetooth & GPS designs,CAN communication, EEprom. UART , RF circuits ,Protocols for networking, wi-Fi routers,OBD diagnosis with CAN bus protocols, Electrical vehicles and AC drives, stepper motor controls. I designed sine wave inverters for standalone and grid tie Inverters. I designed projects like Off line UPS up to 3 KVA, synchronous rectifiers, Solar MPPT chargers, Solar trackers, Battery chargers ,Grid tie inverters design with PLL and feedback control circuit emergency light of 66W and Online UPS control cards, Battery Charging power supplies, LED drivers for PWM controlling and dimming, SMPS, Power supplies. I have experience in schematics and PCB design experience in Altium and ORCAD. I am ready to work for you. Please contact for further discussion.
€666 EUR 20일에
4.9 (52 건의 리뷰)
6.6
6.6
사용자 아바타
I specialize in embedded development on different Microcontroller platforms ( STM32, NXP, Arduino and Arduino Compatible boards). I also have a lot of experience working with different communication protocols including the CAN bus, SPI, I2C, UART, RS252 e.t.c. Please contact me for further instructions concerning your project.
€555 EUR 10일에
4.8 (51 건의 리뷰)
6.3
6.3
사용자 아바타
Hi you will see in my reviews (from toomanyprojects) I have done a project in this area. I can do your project very well.
€555 EUR 10일에
4.6 (23 건의 리뷰)
6.6
6.6
사용자 아바타
Hi, I am very much interested in your project as I believe I have the expertise, knowledge, skills and tools to do your project. I am embedded software developer with more than 8 years of experience of professional embedded software development. Please take a look onto my profile to know more about me. I have quite a lot experience of ARM processors specifically Cortex M0/M3/M4. I have written and used low level, middleware as well as higher level code. I have J-link debuggers, couple of STM32F development boards (STM32F107, STM32F446, STM32F429, STM32F405 and STM32F407). I have quite a lot experience with IAR, ARM GCC and Keil compilers. My recent projects that might tell you my knowledge, 1. STM32F407 Discovery based CAN Data logger to log CAN data into SD Card (SDIO mode) and emulate USB MSC Class to read/write SD Card data and Custom HID Class implementation to send/receive interrupt data. 2. STM32F105 based dual channel CAN transmitter . 3. STM32F107 based dual channel CAN to Ethernet converter. 4. STM32F405 based FATFs to read/write SD Card (both SDIO and SPI). I would recommend to use STM32F105 or STM32F107 as they are cheap, have dual channel CAN, lots of Analog and Digital IOs, have low cost development board, and support GCC compiler. So overall what I am suggesting i quite economical both hardware and software wise. I would like to discuss your requirements further. Let me know if you have any questions. Regards, Ibrahim
€1,000 EUR 30일에
4.9 (17 건의 리뷰)
6.0
6.0
사용자 아바타
I am Pang, web and app developer.I am interesting in your task. I will give you comfortable and cheap service and finish your task on time. Please give a chance!!!
€500 EUR 10일에
4.7 (49 건의 리뷰)
5.6
5.6
사용자 아바타
Hello, client. My number one priority is customer service and satisfaction! I can develop iOS and Android apps, server backend api and admin panel in PHP,MySQL and Website for the app. I have developed many applications involving various functionalities GPS, Photo and Video App, Getting/Uploading data from server(JSON), Google api, Facebook api , Messaging, News and many other implementations. As you have seen, I have developed the various social networking apps & awesome games, so have the more experience than other bidders. As a typical apps, I have developed the taxi booking app, chatting and dating app, shopping cart app and game development etc. I can provide you good quality work from design to publishing the app to stores. Long term maintenance after delivery, also. You will be satisfied by my work at each test step. I will deliver the app in time with perfect implementation of your app requirements. You will get free bug-fixing even after project completion. I would like to build a good relationship with you while working together. Please contact me and let's discuss the project in detail. Best regards.
€555 EUR 10일에
5.0 (3 건의 리뷰)
4.4
4.4
사용자 아바타
I have worked on various mcu or dsp platform for more than seven years. If you want, I d like to discuss details.
€500 EUR 10일에
5.0 (10 건의 리뷰)
4.1
4.1

고객에 대한 정보

국기 (PORTUGAL)
Portugal
0.0
0
12월 15, 2017부터 회원입니다

고객 확인

감사합니다! 무료 크레딧을 신청할 수 있는 링크를 이메일로 보내드렸습니다.
이메일을 보내는 동안 문제가 발생했습니다. 다시 시도해 주세요.
등록 사용자 전체 등록 건수(일자리)
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
미리 보기 화면을 준비 중...
위치 정보 관련 접근권이 허용되었습니다.
고객님의 로그인 세션이 만료되어, 자동으로 로그아웃 처리가 되었습니다. 다시 로그인하여 주십시오.