Design my simple PCB Project.

$30-250 CAD

종료됨

게시됨

약 5년 전

$30-250 CAD

제출할때 지불됩니다

Just a man with an idea. Updated: January 20th, 2019 I've updated this project description (again) to clarify a few more things and correct and earlier error. - Bids exceeding $250 will be immediately deleted. - This project is not intended to be mass produced, and I intend on making the files freely available. So I need to keep the costs down or it's just not realistic. I have a very simple and rather small PCB I need designed (roughly 3.5cm x 2.7cm), essentially a bare bones (2) port USB 2.0 HUB (non-powered) with a microSD card reader connected via one of the hubs ports (direct not via USB), and a MicroUSB Type-B Female connection for the other port. The smaller you can make it the better, even if it has to be double sided. Although I would like to be able to hand solder the components as well as keep it to a single side to help reduce the cost of production. The size of the board should also not exceed 1"x2". No mounting holes are required, neither is an enclosure, like I said, simple! The USB hub should ideally be designed around the FE1.1S as I have easy access to this component, unless you know of another chip that can allow the operation of a USB device and the SD card simultaneously. The HS8836 and HS8826 are also options. You can see some [Example] diagrams for those in the files tab above. These are examples only! You should have prior PCB design experience and an understanding of electronic circuits and be independent and free thinking. I have provided a BOM of primary components below, but don't expect any schematics or a complete BOM. I have attached a block diagram in the files section, yeah...sorry it's the best I can do. You're also welcome to suggest changes to the BOM. You can use Altium, EagleCad, or KiCad for the boards design. That's really about all the information I can provide you, what can I say, my needs are simple, the idea is simple. BOM: (This is only an example of parts. Please feel free to make changes.) FE1.1S or HS8836 (USB 2.0 HUB) 12MHz Frequency Cylindrical Crystal Oscillator 2x6mm Case (Not Required for HS88*6 Chips) 105162-0101 (MicroSD Card Header/Socket) HS8826 (USB 2.0 MicroSD Reader) *Corrected January 18th, 2019

Circuit Design

Electrical Engineering

Electronics

PCB Layout

Product Design

프로젝트 ID: 18499046

프로젝트 정보

62 제안서

원격근무 프로젝트

활동 중 5년 전

돈을 좀 벌 생각이십니까?

이메일 주소

프리랜서 입찰의 이점

예산 및 기간 설정

작업 결과에 대한 급여 수급

제안의 개요를 자세히 쓰세요

무료로 프로젝트에 신청하고 입찰할 수 있습니다

62 이 프로젝트에 프리랜서들의 평균 입찰은 $160 CAD입니다.

@RegulViktor

Hello I am electronic engineer and PCB designer and I can do your task I work in Eagle and Altium (prefer) We can discuss any moments and I believe in our good cooperation Regards

$125 CAD 5일에

4.9

(219 건의 리뷰)

7.7

@ashrafshekh

Hello, Greetings of the day, I have gone through the description & found interesting. I have done many project related to mechanical engineering, 3D modelling, product designing, any kind of simulation, MATLAB, design analysis. I am a standard member here and a full time freelancer, so you can contact me anytime. to brief about me: I am mechanical design engineer by profession and graduate in mechanical engineering with PG in CAD/CAM, ANSYS & Solidworks. I can perform almost all kind of simulation like CFD, FEA, structural analysis etc. I have expertise in many design tools like solidworks, CATIA, ANSYS, 3DMax, Creo MATLAB etc. As i have engineering background with Nine years of industrial experience and very confident about any project related to mechanical engineering field. I have preferred freelancer badge, you can see next to my profile name. You can check my profile and portfolio:- https://www.freelancer.com/u/ashrafshekh.html My bid is negotiable and it depends on the required deliverable. Looking forward to hear from you & feel free to contact me Thanks & regards Ashraf Shaikh

$250 CAD 3일에

5.0

(53 건의 리뷰)

7.2

@arrijal1992

Hi, If you ask my PCB design experience, I've did it since 2012 , and has done lot of projects, from Hobbyst, Robotics, Industrial, IoT, audio, until Military application. I will use Eagle for this project, and 2 layer I guess enough. I just need detailed block diagram of what you wanna build. Let's discuss it over chat . Best Regards, Rijal

$150 CAD 3일에

4.6

(146 건의 리뷰)

7.3

@chuledeco

Hello! I am an electronic engineer with 10 years experience in electronics design and PCB layout. I can do this work using Eagle or Altium based on your detailed description and BOM trying to get the cheapest prototype as possible. If you need further references, please contact me by chat. Regards.

$111 CAD 10일에

5.0

(39 건의 리뷰)

6.8

@quang102

........................................................................................................

$200 CAD 5일에

4.7

(36 건의 리뷰)

6.5

@hudex

Hello sir, I am final year student of electrical engineering i have been working with circuits and devices more than 3 years I work locally for companies Now i want to build up my future here I will give you my best and hopefully you will find me best among all others Tell me your projects detail so we can start work on it Hope to hear good from your side Thanks

$98 CAD 3일에

4.9

(155 건의 리뷰)

6.3

@iamanujpathak

your project is fairly feasible and i can help you with that. i had experience of PCB designing already designed 3 micro controller kits based around arduino using nrf51 micro controller. had good experience in 2-layer PCB designing

$155 CAD 5일에

5.0

(6 건의 리뷰)

5.8

@juanchigarin

Hi Sr, I can design the small PCB board that you need, I will design it in Altium Designer. I made other jobs using GL827L, it is a cheap chip from USB to uSD card and the USB2422 as USB HUB, and all the circuits worked good. I think that is a good option. About the mounting type, the cheapest is manufacturing is the regular SMD, because all the parts that must to be soldered by hand take more time. The SMD are soldered by machines (cheapest). Aboit your BOM, we can discuss that by chat to define the best in this project. I will separate the job in two parts: 1) Schematcis, BOM and libraries. 2) PCB design, folowing your guidelines, 3D files for you can see the board, and 1 review. I will start with the schematics today, once that you approve me the BOM (list of materials), I will start with the PCB, and once that you approve me the size, shape, mounting holes, main placement, I will route the board. Finally I will give you a complete package of files for you can send it to manufacture. I'm electronic engineer with more than 15 years of experience designing circuits and PCB. For more references, please visit my portfolio. Any question, feel free to contact me. Best regards. Eng. Juan M Garin

$155 CAD 3일에

5.0

(20 건의 리뷰)

5.5

@tokumei

Hi there, I've updated my proposal too. I am experienced in designing circuit and PCB and I could provide you help. I have done my research based on the new job description and this looks feasible to me but the board dimension requeirement looks challenging. The suggested part you mentioned is a 4-port hub and the chip has many pin counts and I'm concern on the space if we used this. Based on my research today, i have a part to suggest. There are also other things that I would like to talk about. I hope you could contact me and I'm excited to start to work with you. Thank you, Lawrence

$60 CAD 12일에

4.9

(9 건의 리뷰)

5.6

@olaideejiwole

I am an Electrical Engineer with a masters degree and I have high proficiency in Electrical Engineering, HVAC, LTE system model, Thermal system design, FPGA, Verilog / VHDL, Matlab/ Simulink, Microcontroller, Modeling, optimization, simulation of building energy systems: PCB Layout, Arduino and have been working on Industrial Automatics and Electronics. Our fields of interest are Schematic design, Prototyping, PCB Design, Development of Electronic systems, Firmware and Software development. Once you share the project, I will have a look & confirm if I can do it. I’m honest, creative and a unique person to carry out your tasks given to me. Leaving your project on our hand is privileged; we'll make sure that the project is done in a perfect way and do our best until you satisfied. I would love to discuss this project with you and meet your exact requirements. I am confident I can provide you with top-notch materials that will fit your needs. I pride my work on being professional, of the highest quality and always delivered on time. you can hire me directly through this link https://www.freelancer.com/u/olaideejiwole

$30 CAD 1일에

5.0

(11 건의 리뷰)

4.7

@blexdesign

Hi there,I'm an electronic engineer, And i'm quiet Experienced with High Speed PCB Design and Implementation. I'm an expert in Eagle CAD,EasyEDA and Altium Designer. Can you please send me a message,So we can discuss more about the project? I can design your USB Hub PCB Perfectly and send you the files ready to manufacture the Boards Design is a huge part of my life and I work hard to produce the highest quality, effective, innovative, timeless, designs that my clients will love and I would love to work with you!! :) Thank you Achini

$300 CAD 10일에

5.0

(13 건의 리뷰)

4.6

@SergeyVK77

Hi there, Thanks for the detailed description - this is really helpful. I believe I could help you with designing your project. I have experience with designing memory card readers and USB hubs into various projects. Unfortunately, neither of the parts you suggested will work as a bridge between USB and memory card interface - they are just hubs that convert one upstream USB port to several downstream ports. Fortunately, there are other single-chip solutions that combine USB-hub & USB-to-memory card bridge solutions into a single IC. That approach will do exactly what you want and will be compact enough to fit onto a small PCB. Will be happy to discuss your project over chat in more details. Thanks! Best regards, Sergey

$240 CAD 3일에

5.0

(8 건의 리뷰)

4.6

@soltracker

Yes buddy,,,How r u,,,Its me Imad, have done 200+ projects on various platforms myself and never outsourced a project, U will feel brotherhood,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

$80 CAD 3일에

4.8

(85 건의 리뷰)

5.0

@junaidahmad770

I am an electrical engineer and made similar projects many times. I can design this PCB for you I will try to design a pcb smaller in size. Details of project says that it is easy project. Let me know if you need me for this project.

$200 CAD 7일에

4.6

(20 건의 리뷰)

4.8

@hari1406

Hello sir. As an electrical design engineer best in pcb design and electronic circuit design. I can help you create the sch and board file in eagle cad or altium or kicad. I am sure that you will be satisfied by my work. Thanks.

$155 CAD 3일에

4.8

(26 건의 리뷰)

4.5

@Tomorrow1201

Hi there.I offer you the services for PCB designs, I complete the jobs in Altium designer. I am new on freelancer site, but I am PCB design expert with 10+ years of experience in Circuit designs, PCB designs, software development. You can check our designs in our portfolio. If you want, I will share more designs I completed so far through interview. So I like to discuss the job with you. Lets talk about your project through interview. Thank you.

$100 CAD 3일에

4.3

(8 건의 리뷰)

4.8

@sourabh470

Hello Sir, I have 4 years experience in PCB designing in EAGLE( single multilayer and flex). following are some examples of my work 1. ESP12E wifi + relay board + humidity&temp sensor Smart module 2. ESP12S wifi + relay board home automation board. 3. ESP12E wifi + RC522 RFID + BUCk converter module. 4. atmega328au + hm11(BLE)+ relays car actuator module. 5. atmega328au + nrf24l01 + relays smart switch module. 6. atmega328au + mpr121 capacitive touch smart remote. 7. amega328au + LCD display + hc06(later hm10) + amplifier + strain gauge water mapping module. 8. atmega328au + hm10(BLE) + gyroscope + reed sensor + battery charger smart skateboard module 9. Arduino Uno clone. I will provide you all necessary files ( gerber, smd-coordinate, BOM, Eagle(.brd& .sch) ). please, see my portfolio for more sample of my work. or initiate chat for more detail discussion on your project. thanks.

$200 CAD 6일에

4.9

(17 건의 리뷰)

4.1

@intellisenseIN

Hi there, Yes, We have prior PCB design experience and an understanding of electronic circuits. We can design the USB hub with FE1.1S controller as per the requirements. We have a professional team of Embedded engineers that work in C programming, PCB layout, circuit designing, home automation, RFID, Raspberry Pi & BLE. Kindly spare 10 minutes for the interview. You can review our PCB design work in our portfolio:- https://www.freelancer.com/u/intellisenseIN We will be glad to hear from you! Regards, Intellisense Technology

$277 CAD 20일에

4.9

(3 건의 리뷰)

3.9

@LTEDeveloper

Hello, My name is Sandiy , i have made a lot of PCB and development board and full product development. i have experience with USB hubs , i have made in the past a board with usb flash and mouse in the same case , with button , to can copy the data :D. I can make you the pcb in Kicad or proteus , with the Farnell or mouser products . i will provide you , Full BOM, PCB files , Schematic files , and if you want i can make the order for you for 1-5 boards in china - 35 CAD +customs , Regards, Sandu

$100 CAD 3일에

3.9

(26 건의 리뷰)

5.0

@VirtualBrainInc

Hello, happy new year! I have briefly read the description on pcb project, and I can deliver as per the requirements however I need us to discuss for more clarity on the details, deadline and budget as well. I reach out to see whether the opportunity is still available. If the job’s no longer available, I’d appreciate you throwing my hat into the ring for any similar opportunities in the future. Thank you for your time, I look forward to hearing from you soon, Best Wishes, Kevin M

$200 CAD 4일에