Adduino Inclinometer

€12-18 EUR / hour

진행 중

게시됨

거의 4년 전

€12-18 EUR / hour

The task is to create an inclinometer which shows pitch and roll on a 7 segment led display with some additional features. This can be used as a base code: [login to view URL] [login to view URL] [login to view URL] BOM: - Arduino Nano - LED Display - [login to view URL] - ADXL345 - [login to view URL] - Buzzer - [login to view URL] - Light Sensor - [login to view URL] - Button - [login to view URL] Controls: “CALIBRATE” button Already implemented. “RESET MAXIMUM PITCH AND ROLL” button Already implemented. “SET MAXIMUM PITCH” button The variable is a round number between 1 and 90 degrees. Each press of the button increases the variable by 1. A variable goes back to 1 after 90. During the adjustment, the number is shown on the display. After 5 seconds the new value is saved to EEPROM. When the maximum pitch is reached the module starts blinking and the buzzer is triggered. “SET MAXIMUM ROLL” button Same as for maximum pitch. Other features: Adjust display brightness based on the input from the light sensor.

Arduino

프로젝트 ID: 26678417

프로젝트 정보

7 제안서

원격근무 프로젝트

활동 중 4년 전

돈을 좀 벌 생각이십니까?

이메일 주소

프리랜서 입찰의 이점

예산 및 기간 설정

작업 결과에 대한 급여 수급

제안의 개요를 자세히 쓰세요

무료로 프로젝트에 신청하고 입찰할 수 있습니다

프로젝트를 수여된 사용자:

@Ahmed8033

Hi, I am electronics engineer and has experience of programming in Arduino. I can help you in this task. Inbox me for more discussion.

€15 EUR 40일에

5.0

(3 건의 리뷰)

2.2

7 이 프로젝트에 프리랜서들의 평균 입찰은 €14 EUR입니다./시간

@binyameen441

Dear Client. I have read your description carefully about==ARDUINO I am Muhammad and I am an Electrical engineer having 5+ years of actual experience in Embedded System Design based on Power Supply System Design, IoT, Wearable Device, RF Design, PCB Design, and Simulation. Here are my experiences that I built before. - Schematic and PCB design and Layout using Altium Designer, Eagle, KiCAD, OrCAD. - high-speed, flexible, Multi-Layer PCB design. - DDR, motor control, power converter, UART, SPI, I2C, RF, BLE design - ARM, DSP, MCUs, Arduino, Raspberry pi experiences. you can check my profile portfolio also https://www.freelancer.com/u/binyameen441 If you assign this project to me, I will finish it on time at the utmost quality. If the above offer sounds like something you would be interested in, I'd love to hear from you. Sincerely, Binyameen

€15 EUR 4일에

4.9

(71 건의 리뷰)

5.7

@Provi11

I have 3 years experience in Iot and embedded systems and have worked good hands on both hardware and software. I have worked on many projects that are as follows: Smart lock based on esp8266 Smart water management system based on esp8266 and AWS server Smart energy meter solution Smart curtain controller all the above are based on esp8266 and AWS server i have also worked on electric vehicle and implemented internet of things concept there too. we just need your patience and my hardwork. looking forward to work with you regards Prashant Mishra

€12 EUR 20일에

5.0

(2 건의 리뷰)

2.5

@ZAKI102

Hi. I read your request about Arduino project .I can help you with this problems. I am Ph.D. student an automation and control system, I have a good experience in Arduino, Matlab and control system. I can do it You can see my previous works in my portfolio I have the honor to deal with you

€12 EUR 40일에

5.0

(3 건의 리뷰)

2.2

@z1905z

Hello, I am an Electrical and Electronics Engineer and I completed my master's degree. I designed many electronic circuits and I have academic publications on this subject. As you can see from my portfolio, I have used Arduino before. I worked with many sensor type. I designed many circuits using Arduino and Atmega chip. Thanks to the electronic circuit design programs I can use, I can design and test the circuit. I guarantee free support at all times if there is any problem when the project is over. We can proceed more easily by speaking. I work professionally. Thanks :)

€17 EUR 21일에