Oscilloscope일자리

I want to build a wearable system for gait analysis using an accelerometer. I would like a help with the circuit design and a block diagram that include all the connections (accelerometer-oscilloscope- data logger- etc..)

...complete manual is provided to freelancers interested in developing the project. General characteristics: This product has been created to teach the trouble shooting faults that can occur in a Laptop Computer. The teacher, by specific switches hidden on the side of the external panel, can simulate a specific fault and the students, helped by measurement equipment such as digital multimeter, oscilloscope and by measuring the test points, can identify the fault origin, they can also enhance their understanding of system operation. The programmable faults cover all sub-assemblies/sections of the system and are conceived to train students to locate faults by precisely following a logical guideline from symptom to the possible cause of disoperation. The C5140L units is made of the La...

I need one complete oscilloscope program similar this one DS212 scope: The program must be: -MIKROC PIC32 COMPILLER; -USE PIC32MX MICROCONTROLLER; -USE TFT DRIVER ILI-9341 IN 8 BITS MODE.

Need a Professional Report regarding the PCB Layout design. The PCB is in a soft copy layout form. Need to check for the following 1) check for the working of the pcb. 2) is there any noise or disturbances. 3) are the capacitor filters provide sufficient voltage. 4) oscilloscope readings of signals (drops and spikes if any and their corrective measures) 5) any other deem fit

Hello I'm looking for a computer engineer who can help me and do for me scripting or controlling the input and output of the digilent analog discovery 2 and also measure the impedance of the device and control it fully via MATLAB (it is like writing a firmware for the device) and a code that can also feed input and plot and analyze output and measure the impedance and control the device fully from PC (windows 10), the device can be connected to the PC through a USB cable.

...process and inter-team cooperation • Experience with a task tracking systems, task estimations and time tracking. • Understanding digital electronics and ability to read schematics, analog electronics is a big plus but not obligatory • Experience with FPGA is an asset • Understanding blue prints, engineering drawings and familiarity with PCBs • Experience with measurement instruments (multimeter, oscilloscope). Basic soldering skills. • Basic experience with electronic CAD system is an asset. Sr. Software Engineer: Support and modifying existing code in C++, C# and some Java. Create and modify C# code using .NET Core framework. Ability to code in C++ for cross-platform code for Linux, Windows. Design unit tests using xUnit architecture Design and s...

Im working with an ATMEGA MCU and a DAC (DAC0800) to produce a simple sinusiod wave, triangular and rectangular wave using C language to be produced on the oscilloscope. I require only the codes in C language which will be programmed on my ATMEL AVR. Datasheets will be provided.

I have STM32F745, which digitizes human voice w...following in real-time: 1. generate analytic signal, probably by making Hilbert transform via FFT, zeroizing negative frequencies, reverse FFT, or any better way 2. calculate the envelope of analytic signal 3. calculate the instant phase of analytic signal 4. calculate the instant frequency 5. output the phase shifted signal to the second DAC I should be able to bring both signals from DACs to oscilloscope to see Lissajous patterns. Project can be done on the STM Discovery board, but the delivered solution should work on my PCB with STM32F745. I should be able to compile the delivered source code in Keil uVision V5.24.2.0. Freelancers with experience in STM32F7 FFT and Hilbert please place your bets and portfolios of completed DSP...

I need ECG,pulse oximeter and one oscilloscope on screen,realtime computer based monitoring. Both hardware and software needed

• Execute 32 Electrical and Electronics Test Protocols (e.g. Checking PCBAs quality using oscilloscope, multimeter and interpreting results; Taking system temperature, working current measurements) • Write up Engineering Studies to the test conducted

I need someone to write me a matlab GUI and Program to talk with Newport motor and Keysight Osciloscope. I need to be able to more the motor with step sizes I choose continuously or move to absolute value. Also, the direction of the moving is important to me. * should also think about the boundary conditions of the task (like the end of the motor move etc.) The main purpose is to read read the photo-diode value in the scope while scanning with the motor and it will be displayed and saved on the GUI. The work will be done by connecting to my Computer with teamviewer and you will have access to web camera to see what happens. I'll be close by, if something happens and you need me to turn off and on the devices, I can. Before you submit your proposal, check that you know how to work...

We have developed a measuring device by combining a Rogowski coil and a digital oscilloscope. We are in need of a developer to create the next version of the software. We have an existing code base which will need to be modified to work with the new hardware. Developer will have access to existing code base and all API we have developed and purchased for this project (Analog Arts, Telerik). The software is written in C#.

We would like to combine several simple concepts into a new Python project on Raspian. It will have a simple GUI as a moving StripChart Recorder or Oscilloscope, but moving continuously, with vertical and horizontal scaling options. This is expected to be a modified implementation of MatPlotLib examples. Then we want to add a PID controller from (). Finally, the user should be able to change the set-point of the controller and watch the PID controller converge on the set-point through the continuously moving StripChart Recorder with user controls.

We require a simple oscilloscope project to be implemented using only Verilog code on DE1-SoC board by the latest date of 7th of May as agreed during the chat conversation. This project will comprise of modular Verilog code, fully commented, test-benches for verification and a technical report of the project. Altera Quartus software will be used for the implementation of this project. It is agreed that all of above will be completed at a cost of $210 by 7th of may latest. The oscilloscope developed will take in Analogue readings through the internal ADC on-board, do signal processing and display a continuous waveform through VGA. We require an organised and presentable display screen with waveform scale, and current values shown in text aswell.

A very simple oscilloscope developed using Verilog on Altera software, this project will be based on DE1-SoC Board and is expected to be concluded within a week. Only experienced FPGA engineers please.

I need to create a sound level meter for ambients with 4 MEMS digital microphone, I2S protocol. Also need to show those infos in a 7" LCD display and save those info to a file on the sd card. The hardware connection and communication between the Raspi Pi to communicate with the ICS43434 I2S Digital MEMS Microphone is done, the mic outputs 2 words of 32 bits each, for right and left chann...further. For this first part I need a clean firmware. The firmware should be full accesible as well as the libraries, so later on would be easy to add extra functionality. It would take samples from MEMS microphones, do the FFT with embedded DSP core, apply A-Weighting, calculate dB, display it with one GUI, and log data to csv file on SD card. The Image shows the I2S communication on a O...

Need person(s) with below skills in Chennai, India: 1. Understanding in Test systems to verify software at system level 2. Experience in understanding existing hardware schematics 3. Experience in debugging existing test harness 4. Experience in using Basic hardware like oscilloscope, multi meter, function gen and other related test input system 5. Experience in developing Scripts in any language 6. Experience in developing test setups 7. Experience in C or C++ mandatory. Experience in Matlab,Simulink or Labview preferred. 8. Experience in model based development preferred

generate square wave on arduino. Then build a simple 1st order RC high pass and low pass filter. give the square wave generated to input of rc filter . make a video of output or take pics of output. Output can be seen on oscilloscope or voltmeter. Circuit design and arduino code is attached in the doc file. very simple ,takes 1 or 2 hours

Please do not bid if you have not done work on this hardware. Anyone who is participating on bidding, please show me the examples of work you have done on this in past. I am looking for FPGA guys who have done work on FMCJESDADC1 card, ZC706, RAM Controller, Petalinux. 1. Take data from FMCJESDADC1 card using JESD204B (already implemented) 2. Perform analysis (FFT, etc) 3. Save Data in PL RAM 4. PS gets the data and send it to remote PC over TCP/IP. 5. PS has Petalinux installed 6. Use FPGA Drive (from Opsero) to save the data permanently.

Please do not bid if you have not done work on this hardware. Anyone who is participating on bidding, please show me the examples of work you have done on this in past. I am looking for FPGA guys who have done work on FMCJESDADC1 card, ZC706, RAM Controller, Petalinux. 1. Take data from FMCJESDADC1 card using JESD204B (already implemented) 2. Perform analysis (FFT, etc) 3. Save Data in PL RAM 4. PS gets the data and send it to remote PC over TCP/IP. 5. PS has Petalinux installed 6. Use FPGA Drive (from Opsero) to save the data permanently.

I am looking for FPGA guys who have done work on FMCJESDADC1 card, ZC706, RAM Controller, Petalinux. Please do not bid if you have not done work on this hardware. Anyone who is participating on bidding, please show me the examples of work you have done on this in past. 1. Take data from FMCJESDADC1 card using JESD204B (already implemented) 2. Perform analysis (FFT, etc) 3. Save Data in PL RAM 4. PS gets the data and send it to remote PC over TCP/IP. 5. PS has Petalinux installed 6. Use FPGA Drive (from Opsero) to save the data permanently.

...job, as it has already been done: - interface with distance sensor VL6180X = Not required - interface with weight sensor HX711 = Not required - interface with A4498 Stepper motor driver = Not required - programming control algorithm = Not required My questions: - are you familiar with visual studio 6 or 7 and Atmel ARM processors? - do you have an oscilloscope to check signals coming out of the processor? - do you have an arduino DUE board for testing or can you easily get one? - do you have a JTAG debugger ? It is a private project, so i am not under pressure for deadlines but my budget is limited as i have to pay from my own pocket, not the company money. I need a solid /structured code base wich i can continue programming...

We need to design a circuit for interfacing analog -5V DC to +5V DC with 7 inch TFT Display so that, we can see the voltage change as a waveforms on the TFT display. The number channels should be from 1 channel to 3 channels. It should have all the functions like time/Div (0.1mm to 50mm/sec) and Volt/Div adjustments like in an oscilloscope.

Looking for experienced microcontroller programmer for programming single STM32F767 on our existing board. The connected peripherals are: 1. OLED SSD1306-12864 - SPI 2. Joystick (SKRHADE010) - 5 Active low ...Motor Driving Signal only started when the first SPI data cycle transmited. 10. set up the AD5110BCPZ10-RL7 via i2c, this digital potentiometer is use to control regulated output voltage. This needed to be adjustable via HID(OLED SPI) 11. Programmer must develop using Keil v5. He/she will help to debug along until it is working as described. We expect programmer to have basic tools such as oscilloscope and logic analyzer to perform program checking and troubleshooting. 12. Sample Board will be provided. 12. Attach with the board and sample timing diagram for your r...

Looking for experienced microcontroller programmer for programming single STM32F767 on our existing board. The connected peripherals are: - 1 inch OLED diplay (SSD1306) via SPI - joystick as I/O (up/down/left/right/enter) - output Data* via 4x SPI - 1x stepper motor (DIR/STEP/EN) - ...(the above data is divided into 4 groups) will be provided. Stepper motor speed is adjustable by user. Stepper motor driver is external, thus output as Dir/Step/En. Digital potentiometer is used to control voltage regulator onboard. Programmer must develop using Keil v5. He/she will help to debug along until it is working as described. We expect programmer to have basic tools such as oscilloscope and logic analyzer to perform program checking and troubleshooting. Sample Board will be...

...output, configure P3.7 as output pin. Then, toggle output on pin P3.7 at the same rate as P1.0. 1 • Make sure to turn off the power of (or disconnect) the LaunchPad. Then, connect wires to each of the header pins of P3.7 and GND on your LaunchPad. Next, connect an oscilloscope to the wires to measure the output signal between P3.7 and GND pins. • Compile, load, and run your new program on LaunchPad. • Change the value of SYSTICK_FREQ in the source code according to the table below, then measure the signal frequency from oscilloscope to fill in the table below: • Explain the results in the table above. What is the smallest signal frequency that you can generate correctly using the SysTick timer when MCLK clock frequency is set to 48MHz? Why? Assi...

Engineering company looking for a freelancer able to work in Montreal, Canada area now: - Knowledge of analog and digital electronics design + mixed signal. - Knowledge on Mentor Graphics and Cadence allegro Design Authoring software tools. - Testing knowledge : Lab testing, measurement tools, oscilloscope. - FPGA design knowledge: Vivado(Xilinx), Libero(Microsemi) - Knowledge of PSPICE and LTSPICE simulators - Knowledge of ARINC429, RS845 and ARINC664 interfaces - Knowledge of Aviation standards (or equivalent) : DO254 (Requirement capture, verification and config management) and DO160 (EMI and Pin injection) - Knowledge of DOORS (or any requirement management software) - Full time physical presence in Montreal, Canada area is mandatory. - Duration : 6 months min...

...labview, i have been commissioned to do a simulation but unfortunately I have no high knowledge in labview, i would basically take the maximum and minimum of an oscilloscope acquisition and elaborate it through labview with enough functions Rudimentary, but unfortunately the first part of me is hard to do it, they are several days that "scary" but I can not get a solution or even less on the internet turns something that can be of help. Taken from the discomfort I decided to write here hoping in the help of someone much more experienced than me (this thing I need for a thesis project) My doubt is this: How can I do to read an oscilloscope acquisition and extrapolate the data I need? Because the rest is analysis of what extrapolar and maybe I can put it on with...

i like to use Raspberry Pi to generate 40KHz square waves (1). use raspberry timer, something like below link, to generate 40Khz square wave. the good thing about below one is that i can call the function and control how much time the square wave is there, suc...want. I feel it is impossible or difficult control if i use HIGH and LOW to generate 40KHZ. (3) the output square wave voltage shall be 0-5V (4) need the detailed explanation of code, the library used, the wiring, the circuits, ..., and how to implement the code, and i will test it with my oscilloscope. You will have to find a way to prove and to demo it is working, and the sqare wave output is controllable, ... (5) Phython and C language -- i beleive Again, I have oscilloscope and I will t...

We would like to hire someone to design (no PCB needed, only schematic but the simulation needs to be as accurate as possible) a crystal notch at a specific frequency (in the MHz). We already have the quartz, we also have every parameters of each piece (Fs, Fp, Cs, Cp, Q, Rs ...) This filter needs to be matched at 50ohm IN and OUT. Attenuation should be at...accurate as possible) a crystal notch at a specific frequency (in the MHz). We already have the quartz, we also have every parameters of each piece (Fs, Fp, Cs, Cp, Q, Rs ...) This filter needs to be matched at 50ohm IN and OUT. Attenuation should be at least 90db. Maximum Insertion loss : 6db Min Bandwidth : 1kHz We have some measurement instruments if needed : VNA, Spectrum analyser, oscilloscope, crystal measur...

hi there, the job is to retrieve a waveform coming from Agilent 86100C Oscilloscope on Labview software. the Scope is connected to a laptop vie GPIB/ USB interface. The Oscilloscope's drivers are given by Keysigth company and few example to control the scope. our Scope display an optical pulse of 8ps period after using an external trigger to trace the waveform. i have tried to use the existing examples provided by Keysigth, but i did not succeed. Things i think need to be modified on the existing example like ; time out, VISA READ AND WRITE COMMANDS and maybe more. if you are interested, i will be granted team view access to the pc which is connected to the Scope to test VI's. that will speed up the process a little. i am looking forward to hearing from you soon, Best Wish...

Hi Znstechnologies, This is a small project in which you need to provide Adwords CPC & Negative keywords for " Oscilloscope" . You must provide top 3 keywords about Solar Energy both for CPC & negative keywords as well.

Labview Programmer needed; Must be local and work on site (charlestown) Need a Labview programmer Need help with it, writing a user interface for this device We are Labview Programmer but have two weeks to finish the job. The Labview programmer will have support from us on writing the program for the user interface but; if you have never used labview it will be hard; to follow us payment, contract by finish job; not hours estimated time two weeks! If you are good programmer could be done in less than 40 hours again, you are part of the team just writing one-part of the whole program respond with reference or training in labview thanks

The project consists in supporting me in the debugging of an embedded software for a microchip dspic33fj. The microcontroller is conne...dspic33fj. The microcontroller is connected to a temp sensor (RTD 100ohm, analog signal) through an ADC. The analog signal, the temp value, has been monitored on oscilloscope. Voltage value is correct and stable. While debugging the software, the ADC reading revealed to be inacurrate (900mV -> 550, when normally around 280) and unstable (value fluctuating between 550 and 750). Looking for an experienced freelancer to support me in finding the bug. Prefered: worked with DSPIC. Will provide the electrical schematics, the software, the datasheets for the microcontroller. at my disposal: PCB, programmer, oscilloscope, heater (...

The project consists in supporting me in the debugging of an embedded software for a microchip dspic33fj. The microcontroller is conne...dspic33fj. The microcontroller is connected to a temp sensor (RTD 100ohm, analog signal) through an ADC. The analog signal, the temp value, has been monitored on oscilloscope. Voltage value is correct and stable. While debugging the software, the ADC reading revealed to be inacurrate (900mV -> 550, when normally around 280) and unstable (value fluctuating between 550 and 750). Looking for an experienced freelancer to support me in finding the bug. Prefered: worked with DSPIC. Will provide the electrical schematics, the software, the datasheets for the microcontroller. at my disposal: PCB, programmer, oscilloscope, heater (...

needed a LabView project to create VIs containing Signal Generator, Oscilloscope, and FTT spectrum analysis. see this youtube link will help you understand what I want:

I need a simple Android app which can display data from an arduino through bluetooth. I want it to be used as multimeter and at the same time a simple oscilloscope to graph data. I already have a design for it, I just need it to be built. If possible, I want it to be done by sunday or monday. Please see my attachments for my proposed design of the mobile app.

Harry, hello! Before 10 months ago I hired for you for a project including voice recording for an automotive oscilloscope VISO. I have another script that needs to be read and two more videos are comming soon. Are you willing to take the jobs?

Person required for LabVIEW project for developing a Electrical Power test bench. to develop a double pulse signal with NI module 9402 and connect to the oscilloscope. There is a working model already,but some things needs change for better performance and relaiability

I am working on an audio plugin oscilloscope. Here are some videos of it in action: All the code is custom pixel writing code all done on the CPU. This turned out to be a disaster because CPU usage would not allow me to sell this product, no one would be able to run it. This forced me to move to OpenGL. I am so glad I did, it surpassed my expectations. Here it is in action: With a band of friends having little to no openGL we got that far. It's awesome. The code is simple/short and I can walk you through it. Having no experience with openGL I am having trouble adding just the last few features that were present in the old CPU version. Mainly, I need to add 2 FBOs (frame buffer

...direction. It does have a tiny reverse current that can become large if the reverse bias exceeds a 'breakdown voltage'. The forward current increases exponentially with bias until it saturates. This behavior can be shown as a graph on an oscilloscope if you have the correct electronics. This project is the design and production of these electronics. The student doing this project will have to design and produce an electronic instrument that can take input from a signal generator and a diode and output the characteristic curve (I,V) for the diode to an oscilloscope. This project will be a great help to PH405 and EP406. Multiple pin-hole lens Professor Michael McInerney A pin hole is able to act as a lens but requires a bright light source. Severa...

I have a requirement for a PWM based three phase Micro Hydro Controller or ELC to be designed and prototyped. The ELC( Electronic Load Controller) is intended to control the voltage and frequency of a synchronous generator of a stand- alone micro hydro power generator. The generator frequency variation is in inverse proportion to the loading condition where ELC maintains ...snubber circuits. Fast switching of IGBT generates significant radio interference. Please ensure that this does not impact the performance of the ELC 7) I also need the schematics, part list, pcb layout& design, source code etc of the ELC 9) The project will be completed when the ELC is working satisfactorily in all aspects. I have a Pump driven Micro Hydro Turbine setup and Hantek DSO 8060 oscilloscope to...

...that turns your Discovery board into a USB-controlled signal generator. The signal generator should be able to output three different types of signal:  A constant voltage, with configurable amplitude.  A sine wave, with configurable amplitude and frequency.  A square wave, with configurable amplitude and frequency. The following three figures show how these signals should look on an oscilloscope. In this the amplitude of all the signals is 2V and the frequency of the sine and square waves is 5Hz When the program starts, it should send a command over the serial link asking the user what function they would like to generate. The command they type should be in one of the following formats:  constant <amplitude>  sine <amplitude> <frequency>  s...

I need to design electric simulator so can design simple circuit and read voltage and current and se oscilloscope and need to run as swf format like this one ""

I need a PCB designed and assembled with these features. We can discuss further. Board based on Beagleboard Beaglebone Black Only the basics are needed. Sitara CPU, PCM5101 Audio PLL, Ethernet, I2C for Apple Auth chip and a TDA1540 DAC connected to the UART using Simultaneous Data Protocol WiFi, USB, video, RCA output, Analog In, Analog Out not needed Add a TDA1540 DAC per channel u...PCM5101 Audio PLL, Ethernet, I2C for Apple Auth chip and a TDA1540 DAC connected to the UART using Simultaneous Data Protocol WiFi, USB, video, RCA output, Analog In, Analog Out not needed Add a TDA1540 DAC per channel using serial connection i2c required for apple auth Requirements: Must know Hardware, PCB Design, some Linux, Digital Electronics, Audio Must have Distortion Analyzer, Oscill...

I have a Windows MFC application with an oscilloscope like waveform display window that uses too much CPU time. I am looking for someone who can use OpenCL or similar to offload the drawing of the waveform from the CPU. The waveform display shows 1024 8-bit samples connected by straight line segments drawn in a resizeable window. The window is updated at around 25 fps, but for each update, approximately 40 waveform need to be drawn - each one drawn over the ones before resulting in a mass of overlapping waveforms. I require someone who can select an appropriate solution to provide platform independent GPU acceleration for my application and assist in the integration into an MFC project in Visual Studio 2008.

I need this simple project in 1 day time. It involves using concepts of programming and electrical engineering. The project is "Need to code amplitude modulation and amplitude demodulation on C language. Basically take an input signal from oscilloscope to a DSK board perform AM modulation on it using C and then output it to other DSK board, perform AM demodulation using C and the output the original signal back to oscilloscope" Only genuine bidders please. My budget is around 35-45 usd. I have attached a file for reference, you may find it useful.

Develop a mobile app for Android and iOS that has the following properties Phase 1 1) Ability to record sound from Bluetooth microphone device 2) Ability to save sound to phone 3) Ability to share sound file with social media, email, and text messaging 4) Have a visual representation of the sound as it is being recorded. I.e. Line graph similar to an oscilloscope showing a heart beat. 5) Provide the ability to connect to a specific bluetooth device and verify that it is synced. 6) Provide ability to record audio from a hands free device using the BT HFP protocol and, if possible, the A2DP protocol. 7) Save sound file as a MP3 or WAV file format. 8) Display Splash screen on start 9) Ability to start and stop recording from BT Device 10) Ability to play recorded ...

Develop a mobile app for Android and iOS that has the following properties Phase 1 1) Ability to record sound from Bluetooth microphone device 2) Ability to save sound to phone 3) Ability to share sound file with social media, email, and text messaging 4) Have a visual representation of the sound as it is being recorded. I.e. Line graph similar to an oscilloscope showing a heart beat. 5) Provide the ability to connect to a specific bluetooth device and verify that it is synced. 6) Provide ability to record audio from a hands free device using the BT HFP protocol and, if possible, the A2DP protocol. 7) Save sound file as a MP3 or WAV file format. 8) Display Splash screen on start 9) Ability to start and stop recording from BT Device 10) Ability to play recorded sound over ...

Develop a mobile app for Android and iOS that has the following properties Phase 1 1) Ability to record sound from Bluetooth microphone device 2) Ability to save sound to phone 3) Ability to share sound file with social media, email, and text messaging 4) Have a visual representation of the sound as it is being recorded. I.e. Line graph similar to an oscilloscope showing a heart beat. 5) Provide the ability to connect to a specific bluetooth device and verify that it is synced. 6) Provide ability to record audio from a hands free device using the BT HFP protocol and, if possible, the A2DP protocol. 7) Save sound file as a MP3 or WAV file format. 8) Display Splash screen on start 9) Ability to start and stop recording from BT Device 10) Ability to play recorded sound over ...